Troubleshooting
Roborock Not Connecting to Wi-Fi
What Roborock says to check when a robot will not join your network or shows offline in the app: the band, the router, the app permissions, then the Wi-Fi reset.
A Roborock that will not join your Wi-Fi is nearly always stuck on one of a few things: the wrong band, a router setting the robot does not support, a phone that is blocking the app from doing its job, or a setup attempt that needs a clean restart. Roborock's own support pages cover each of them, and the first one is the cause more often than any other.
This guide follows what Roborock publishes, in the order that is quickest to check. We stick to the maker's statements and its manuals, and where a page does not say something, we say that instead of guessing. The pages are listed at the end with the date we read them. If your robot connects but misbehaves in other ways, our robot vacuum troubleshooting hub sorts the symptoms by cause. If you are not sure which series you own, our Roborock models explained guide helps you place it.
Check These First
-
Join the 2.4 GHz network, not 5 GHz
Roborock's help pages say its robots currently support only the 2.4 GHz Wi-Fi band and not 5 GHz. If your router broadcasts two networks, pick the 2.4 GHz one during setup. Roborock says it is usually labeled with a 2.4 or 2G suffix.
-
Choose your home network, not the robot's
During setup the robot creates a temporary network of its own. Roborock says to choose your home Wi-Fi and enter its password, instead of the robot's network.
-
Retype the password
Roborock's first suggestion for a failed connection is to confirm the password you entered is correct. A single wrong character is enough to stall setup.
-
Allow the app's permissions
Roborock says to enable location permission for the app, and on iOS 14 or later to enable local network access as well. A phone that blocks these can stop setup before the robot is asked to join anything.
-
Turn off cellular data and any VPN
Roborock says to disable the phone's cellular network or VPN and try again. Both can pull your phone off the same network the robot is trying to join.
-
Restart the robot and the router
Roborock lists a reboot of both devices as its own step before you try setup again. Power the router off and on, restart the robot, then start the pairing from the beginning.
Router Settings That Stop a Roborock Connecting
If the checks above did not help, look at the router. Roborock publishes only a short list of router-side causes, and we keep to it. Anything else you read about band steering, channel width or WPA3 comes from third parties, not from the maker.
The 2.4 GHz Band Must Be On and Visible
Roborock says that if you can see a 5 GHz network but not a 2.4 GHz one, the 2.4 GHz network may be switched off, and you should enable it in the router settings. On a dual-band router that shows two names, choose the 2.4 GHz name. On one that shares a single name across both bands, Roborock says to try connecting to it first, and if that fails, to contact your internet provider or router maker about separating the bands or getting help with the connection.
Security Type
Roborock says the robot does not support WEP encryption. If your network still uses it, change the network to WPA or WPA2. This is rare on current routers, but it turns up on old ones that were never reconfigured.
Special Characters in the Name or Password
Roborock says that if the Wi-Fi name or password contains characters such as !, @, # or $, you should remove them in the router settings. This is the quickest router change to make and it removes one common cause of an abnormal pairing.
DNS
For owners comfortable with router settings, Roborock's page also suggests changing the DNS server to 8.8.8.8. It is an optional step, listed after the simpler ones, so leave it until the others have failed.
What Roborock Does Not Say
The pages we opened do not mention guest networks, MAC address filtering, firewall ports or a static IP address, so we cannot tell you whether they cause or cure a failed connection. If you run any of those on your router and nothing else has worked, turning them off for the duration of setup is a reasonable test, but that is our suggestion and not Roborock's.
Roborock App Fixes
The setup order matters, and the manuals show where owners trip. Some Roborock models can be added in either the Roborock app or the Xiaomi Home app (also called Mi Home). Roborock's S7 manual says the robot supports both and that you should choose the one that meets your needs. Do not set the same robot up in both at once, and do not assume your model works with both. Check your own manual.
Add the Robot as a New Device
Roborock's S8 manual says that if you cannot connect because of router settings, a forgotten password or another issue, you should reset the robot's Wi-Fi and add it as a new device. In the Roborock app the manual says to tap the Scan to Connect button. In Xiaomi Home it says to tap the plus sign in the top right corner. In both cases, follow the in-app prompts, which the manual notes can change with app updates.
Do It Within 30 Minutes
The same manual says that if the robot waits more than 30 minutes for a connection, its Wi-Fi turns off automatically, and you must reset Wi-Fi before trying again. If a setup attempt has been sitting for a while, that is the likely reason the robot no longer shows up. Reset the Wi-Fi first, then start the pairing straight away.
Update or Reinstall the App
The Roborock pages we read do not give an app reinstall step. Reinstalling is a common general fix for a stuck app, and it is harmless, but it is not something Roborock lists, so treat it as a last test on the phone side.
Wi-Fi Reset by Series
A Wi-Fi reset clears the robot's network link and puts it back into pairing mode, without touching the rest of its settings. It is lighter than a factory reset, so try it first. The steps differ between older and newer robots, and Roborock does not publish one sequence for every series, so we give only what the manuals state.
How to Reset Wi-Fi on a Roborock S7 or S8
-
Open the top cover
The manuals say to open the upper cover and find the Wi-Fi indicator.
-
Press and hold the two buttons
The manuals tell you to hold two buttons together until you hear the voice alert "Resetting Wi-Fi". The pages we opened lost the button names in the text, so we do not print them. Your printed manual or the diagram in the app shows the pair for your model.
-
Watch the Wi-Fi indicator
The reset is complete when the indicator flashes slowly, which means the robot is waiting for a connection. Fast flashing means it is connecting, steady means it is connected, and off means Wi-Fi is disabled.
-
Add the robot as a new device
Open the app, add the robot again with your phone on the 2.4 GHz network, and follow the prompts. Do this soon, because the Wi-Fi turns off after 30 minutes of waiting.
Other Series
We could not open a Roborock page that gives the Wi-Fi reset sequence for the Q series, the Qrevo or the Saros, so we do not print one. Using a combination from another series can trigger a different reset than the one you wanted. For those robots, use the manual for your exact model, or the in-app guide.
Do Not Confuse It with the Reset Button
Roborock's Qrevo help page describes a different step for internal errors: open the top cover and press the Reset button. It warns that this restores all current settings to factory defaults, including Wi-Fi and scheduled cleanups, so you would have to set the Wi-Fi up again afterward. That is a system reset, not a Wi-Fi reset. Our how to reset a Roborock guide explains the restart, Wi-Fi reset and factory reset side by side, so you can pick the lightest one that fits.
Still Offline?
If the robot pairs but keeps dropping, or never connects after all of the above, narrow it down in this order.
Check the Robot Is Close Enough
A robot that sits at the far end of the house may sit at the edge of your signal. Roborock's pages do not set a distance, so test it by moving the dock, or by standing the robot near the router during setup and moving it back afterward. If it connects near the router and drops in its usual spot, the signal is the problem, not the robot.
Check Whether the Router Changed
A new router, a renamed network, a changed password or a firmware update that switched on a new security mode can all break a link that worked yesterday. Roborock does not describe these cases, but the fix is the same as for a first setup: reset the robot's Wi-Fi and add it again.
Charging and Hardware
A robot that dies on the way home or will not wake up is not a Wi-Fi problem. Our Roborock not charging guide covers the dock, contacts and battery. If the robot keeps stopping for no clear reason, dirty sensors are a common cause, and the clean Roborock sensors guide shows which ones to wipe.
When to Contact Roborock
Roborock's own page ends the same way every time: if the connection still fails, contact Roborock Customer Support. Have the model and your router type ready. Owners with a Roomba on the same network can compare the steps in our Roomba not connecting to Wi-Fi guide, since the 2.4 GHz rule is common to both brands.
Roborock Wi-Fi FAQ
Sources
- Roborock Help, Qrevo troubleshooting, what to do when Wi-Fi connection fails or the robot shows as offline in the app, help.roborock.com, read on November 20, 2026 Source for the 5 GHz statement, the password check, location and local network permissions, choosing the home network, special characters, WEP, DNS, restarting the robot and router, VPN and cellular data, contacting support, and the Reset button warning.
- Roborock Help, Qrevo FAQs, 5 GHz support and dual-band routers, help.roborock.com, read on November 20, 2026 Source for the 2.4 GHz only statement, choosing the 2.4 GHz name on a dual-band router, the combined network name advice and enabling a disabled 2.4 GHz network.
- Roborock S8 (S80ULT) manual, Connecting to the App, via ManualsLib, read on November 20, 2026 Source for the Wi-Fi reset steps and voice alert, the indicator states, the Scan to Connect and Xiaomi Home add steps, the 2.4 GHz only note and the 30 minute Wi-Fi timeout.
- Roborock S7 manual, Connect to the App and Reset Wi-Fi, via ManualsLib, read on November 20, 2026 Source for the same Wi-Fi reset sequence on the S7, the indicator states and the 2.4 GHz only statement. A preceding page confirms that the S7 supports both the Roborock and Xiaomi Home apps.