Troubleshooting

Roomba Not Connecting to Wi-Fi

The checks iRobot lists for a Roomba that will not join your network, in the order that usually solves it: the band, the router, the app, then a reset.

Roomba not connecting to Wi-Fi: a round robot vacuum on the floor with a home router in the background

A Roomba that will not join your Wi-Fi is usually stuck on one of three things: the wrong band, a router setting that gets in the way, or a setup attempt that needs a clean restart. iRobot's setup pages cover all three, and most owners find the cause in the first of them.

This guide follows iRobot's own advice, from the quick checks to the reset. It does not guess at router quirks that iRobot does not mention, and where the maker is silent we say so. Every fix is attributed to the iRobot page it comes from, and the pages are listed at the end. If the robot connects but misbehaves in other ways, our robot vacuum troubleshooting hub is the place to start.

Check These First

  1. Put your phone on the 2.4 GHz network

    iRobot says some robot models support only 2.4 GHz, and that for those your mobile device needs to be on 2.4 GHz Wi-Fi during setup. Models that support 5 GHz do not need this. If you are not sure which yours is, assume 2.4 GHz.

  2. Pick the right network name

    If your router shows two similar names, one with 5G on the end and one without, iRobot says to choose the one with no extra label or with 2G or 2GHz. That is usually the 2.4 GHz network.

  3. Check the password and the name

    iRobot warns that special characters such as !, #, $, % and & in your network name or Wi-Fi password may cause an error during setup. Retype the password carefully, and if your name or password uses those characters, try a simpler one.

  4. Move the dock close to the router

    iRobot's setup steps say to place the dock on a level, obstacle-free surface as close to the router as possible, plugged in with its light on. You can move it back afterward.

  5. Turn on Bluetooth and location on your phone

    The setup steps also ask for Bluetooth and location services to be on, with Precise Location enabled. A phone that is blocking these can stall setup before the robot is even asked to join the network.

  6. Update or reinstall the app

    iRobot suggests uninstalling and reinstalling the app, which clears its cache and puts you on the latest version.

Router Settings That Block Roombas

If the checks above did not help, look at the router. iRobot's requirements page is short and specific, and it does not name every setting people suspect, so we stick to what it says.

Mesh Systems

Mesh systems often combine the 2.4 GHz and 5 GHz bands under one name, so a robot that only does 2.4 GHz can end up unable to find its side of the network. iRobot says you may need to temporarily switch off 5 GHz on the mesh system during setup, using the mesh maker's guide, and turn it back on once the robot is connected. iRobot also says each device on the network, including the main and secondary routers, should have its own IP address, because duplicate addresses cause networking problems.

Guest Networks

iRobot says guest networks are not recommended. Put the robot on your main network, not the guest one.

Special Characters

This is the setting most owners can change in a minute. iRobot says special characters in the network name or password may cause a setup error. A plain name made of letters and numbers removes the question.

Firmware and Firewalls

iRobot says to update your router's firmware. It also lists the ports a firewall needs to allow, which matters only if you have strict rules set up: the robot uses TCP 443, TCP 8080 and 8883, UDP 123 for time, and DNS on port 53 going out, plus UDP 5353 and 5678 for discovery inside the home. For firewall help, iRobot points owners to their internet provider or router maker.

What iRobot Does Not Say

The pages we read do not mention band steering, WPA3 or a specific channel, so we cannot tell you those cause or cure a failed connection. If your router has a band steering option and the robot keeps failing, turning it off for the duration of setup is a harmless test, but that is our suggestion, not iRobot's. Likewise, a few older routers are listed by iRobot as needing a security or channel width change, or as incompatible, so if you own an old router and nothing else works, iRobot's requirements page is worth reading for your model.

Fixes in the iRobot Home App

Setup in the app is a short sequence, and the order matters because the steps differ between older and newer robots.

The Setup Sequence, With the Fixes iRobot Lists

  1. Connect the phone to the network the robot will use

    Do this before you open the app. On a dual-band router, make it the 2.4 GHz network for robots that need it.

  2. Add the robot from the main menu

    Open the menu, choose Add your product, and follow the prompts for the nearby robot or the model you select.

  3. Follow the order the app shows

    iRobot says on newer models you press the robot's button when prompted, then choose your network and enter the password. On older models you enter the password first, then press the button. Stay on the screen until the connection completes.

  4. Reboot the robot and try again

    If setup fails, iRobot says to keep the robot on the dock and hold CLEAN for about 20 seconds until you hear a tune, then try again. This is a reboot, not a reset, and it does not erase anything.

  5. Restart the router

    iRobot says to unplug the router for 10 seconds, plug it back in, and wait 2 minutes for it to boot before retrying. On a mesh system, reboot the main router first, then unplug and replug each secondary one.

  6. Name the robot and finish

    Once it connects, name the robot and complete setup. If the app later says the robot is offline, repeat the checks above before assuming the robot is at fault.

Wi-Fi Reset by Series

If rebooting and a router restart do not work, the next step is to reset the robot so it forgets its old network. iRobot's reset article describes the button combinations by series. It describes these as factory resets. The article we read does not give a separate Wi-Fi only reset, so treat the list below as the full reset. When it is done, add the robot again from the app as if it were new.

Reset Buttons by Roomba Family, From iRobot

  1. s Series and i Series

    Hold Home, Spot Clean and Clean together until the ring around Clean swirls.

  2. j Series and Combo 10 Max

    Remove the dust bin. Hold Clean for 7 seconds until you hear a tone, then tap Clean twice more to confirm.

  3. e Series

    Hold Home, Spot Clean and Clean for 20 seconds, then release.

  4. 900 Series

    Hold Dock, Spot Clean and Clean until all the LEDs light up.

  5. Wi-Fi connected 600 and 800 Series

    Hold Dock, Spot Clean and Clean until the robot beeps, then release.

  6. Roomba Combo

    Open the lid and hold the recessed Reset button, to the left of the On/Off switch, for ten seconds.

  7. 100/1000, 200/2000, Plus 400, 500 and 600, and Max 700 and 800

    Hold Home for 5 seconds and wait for the voice prompt, then hold Home and Power together for 5 seconds and keep holding until the robot gives instructions.

Still Offline?

If the robot still will not join after a reboot, a router restart and a reset, work through this short list before you contact iRobot.

  • Confirm your robot's exact model. Our Roomba models explained guide helps you read the name on the robot, because the band support depends on the model.
  • Try another phone, or another network name, to rule out the phone.
  • Temporarily switch off 5 GHz on a mesh or dual-band router, connect the robot, then switch it back on.
  • Check for a red or flashing light on the robot itself, which can point at a fault that has nothing to do with Wi-Fi. Our Roomba red light guide reads each pattern.

iRobot's own answer when none of this works is the same on every page: contact iRobot Customer Care. For a Roomba that connects but cannot reach the cloud, it is also worth knowing how the company's situation affects the app. Our iRobot bankruptcy page covers the state of the app and support, and only that.

If you own a Roborock and not a Roomba, the checks are similar but the app and the resets differ. See our Roborock not connecting to Wi-Fi guide.

Roomba Wi-Fi FAQ

Put your phone on the same network the robot will use, then open the iRobot Home app, choose Add your product and follow the prompts. If that fails, reboot the robot by holding CLEAN for about 20 seconds on the dock, and restart the router. A factory reset is the last step, because it removes the robot from your account.
The usual causes iRobot lists are a phone or network on the wrong band, special characters in the network name or password, a guest network, a mesh system combining 2.4 GHz and 5 GHz, or a router that needs a restart. Fix those in that order, then reboot the robot and try setup again.
Start with a reboot: keep the robot on the dock and hold CLEAN for about 20 seconds until you hear a tune. If it still does not respond, use the button combination for your series, such as Home, Spot Clean and Clean together on an s or i Series, which iRobot describes as a factory reset.
Some do and many do not. iRobot says some models support only 2.4 GHz, while others support both bands, so it depends on the model. If you are not sure, connect the phone and the robot to your 2.4 GHz network during setup. A mesh system may need 5 GHz switched off temporarily.
Yes for basic cleaning: the robot has its own buttons, and cleaning starts with a press of CLEAN. What you lose without Wi-Fi is the app, including schedules, maps and remote start. Which features work offline varies by model, and we have not confirmed it for each series, so check your manual.

Sources

  1. iRobot Customer Care, Setting up your Wi-Fi Connected Robot with the iRobot HOME App, homesupport.irobot.com, read on November 20, 2026 Source for the setup steps, the 2.4 GHz phone tip, the similar network name tip, the 20 second CLEAN reboot, the router restart, reinstalling the app and the mesh network advice.
  2. iRobot Customer Care, Wi-Fi requirements article, homesupport.irobot.com, read on November 20, 2026 Source for the special characters warning, the band support statements, the guest network and mesh IP address notes, the router firmware advice and the firewall ports.
  3. iRobot Customer Care, Why factory reset your robot and how to do it, homesupport.irobot.com, read on November 20, 2026 Source for the reset button combinations by series, what a factory reset erases, and the Save maps during factory reset option.